Sato Cl608e Driver For Mac

카테고리 없음

Sato Cl608e Driver For Mac

consgitentuacumen 2021. 5. 30. 01:32

Canon Printer Driver For Mac

1
Service Manual
3
Table of Contents
- 7
  Overview
- 8
  Physical Characteristics
- 9
  Printer Features
- 9
  Rear Panel
- 12
  Operation PanelDisplays
- 14
  Components
- 14
  Sensors and Switches
- 15
  Switches and Sensors
- 16
  Ribbon
- 16
  Installation Considerations
- 16
  Optional Accessories
- 17
  Environment & Approvals
- 17
  General Printer Specifications
- 20
  Character Fonts
- 21
  Bar Codes
23
Section 2. Configuration
- 23
  Dip Switch Settings
25
Printer Set Up
- 29
  Default Settings
30
Lcd Panel Configuration
- 31
  Normal Mode
33
Pitch Offset Adjustment
- 35
  Advanced Mode
36
Print Offset
- 38
  Character Pitch
- 38
  Exit Advanced Mode
- 39
  Card Mode
- 53
  Service Mode
- 54
  Counters Hd Dsp Cut Life
- 54
  Counters Mode
- 55
  Test Print Mode
- 56
  Default Setting Mode
  - 57
    Maintenance Mode
  - 58
    All Clear Mode
- 59
  Download User Defined Protocol Codes
- 60
  Hex Dump Mode
- 60
  User Download Mode
- 62
  Sample Test Labels
63
Section 3. Interface Specifications
- 63
  Overview
- 63
  Interface Types
  - 64
    Available Interfaces
  - 65
    The Receive Buffer
- 66
  Receive Buffer
- 66
  Ieee 1284 Parallel Interface
  - 66
    Data Streams
  - 68
    Rs232c Serial Interface
  - 68
    General Specifications
  - 68
    Electrical Specifications
  - 69
    Cable Requirements
  - 70
    Rs232c Interface Signals
70
Ready/busy Flow Control
- 71
  Universal Serial Bus (USB) Interface
- 71
  X-on/X-off Flow Control
- 72
  Bi-Directional Communications
- 72
  Ethernet Interface
- 73
  Accessory (EXT) Connector
  - 74
    Standard Operation
  - 75
    Repeat Print
  - 75
    Error Signals
77
Section 4. Electrical Checks and Adjustments
- 77
  Overview
- 78
  Steps Prior to Some Procedures
- 80
  DC Power Voltage Checks
- 83
  Potentiometer Assignments & Adjustments
  - 84
    A Print Position Adjustment
  - 85
    B Print Position Adjustment
  - 85
    Factory Mode
  - 85
    Counter Clear
  - 85
    Print Size
- 86
  Label Gap Adjustment
- 87
  Eye-Mark Adjustment
88
Offset Label Stop Position Adjustment
- 89
  Ribbon Sensor Verification
- 90
  Ribbon Sensor Adjustment (Near End)
- 91
  LCD Display Adjustment
- 92
  Print Darkness Adjustment
93
Section 5. Mechanical Adjustments
- 93
  Overview
- 95
  Ribbon Clutch Adjustments
  - 95
    Rewind Clutch
  - 95
    Unwind Clutch
- 97
  Print Head Position Adjustment
- 99
  Print Head Balance Adjustment
- 100
  Ribbon Roller Adjustment
- 102
  Feed Roller Adjustment (Label Tracking)
- 103
  Timing Belt Tension Adjustment
- 104
  Head Latch Adjustment
- 105
  Notch/Gap Sensor Adjustment
107
Section 6. Replacement Procedures
- 107
  Overview
- 109
  Replacing the Main Circuit Board
- 114
  Replacing the Fuses
- 116
  Replacing the Power Supply
- 118
  Replacing the Stepper Motor
- 120
  Replacing the Timing Belts
- 123
  Replacing the Print Head
- 126
  Replacing the Platen
- 130
  Replacing the Ribbon Drive Clutch Washers
- 134
  Replacing the Ribbon Motion Sensor
- 137
  Replacing the Paper End Switch (Micro-switch) and the Bottom Half of the Notch/Gap and Eye-Mark Sensors
- 141
  Replacing the Top Half of the Notch/Gap Sensor
- 144
  Replacing the Display Panel or Keyboard
147
Section 7. Factory Resets
- 147
  Overview
- 148
  Maintenance Mode
- 149
  Clear Head Counters
- 150
  Clear Dispenser Counter
- 151
  Clear Cutter Counter
- 152
  Clear EEPROM
- 153
  Sample Test Prints
155
Section 8. Troubleshooting
- 156
  Initial Checklist
- 156
  The IEEE1284 Parallel Interface
156
SATO CL608e/CL612e Service Manual
- 158
  The RS232C Serial Interface
- 158
  The Universal Serial BUS (USB)
- 159
  Installation Problems
160
Intermittent Problems
160
Tcp/ip Troubleshooting
161
Netware Troubleshooting
- 163
  Resetting the Print Server
- 163
  Windows 95/98 Peer-to-peer Troubleshooting
- 164
  Error Signals
- 165
  Troubleshooting Tables
166
Print Quality Problems
- 170
  Head Pattern Examples
- 171
  Hex Dump Diagnostic Labels
173
Section 9. Optional Accessories
- 173
  Overview
174
Label Cutter Kit Installation
187
Pcmcia Memory Expansion Installation
- 192
  Flash Memory Expansion Installation
- 193
  Real Time Clock Installation
  - 195
    Test Print
  - 195
    Factory Reset Procedure
- 199
  Overview
- 199
  Spare Parts List
- 201
  Base Cover Assembly
- 210
  Frame Assembly
- 216
  Print Head Assembly
- 221
  Ribbon Assembly
- 226
  Feed Roller Assembly
- 228
  Main PCB Assembly
- 229
  Interface Option
- 231
  Dispenser Assembly Option
- 238
  Cutter Assembly Option
- 241
  PCMCIA Memory Option
243
Index

Canon Printer Driver For Mac

SATO CL608e Printer For advanced technology and high-speed performance the CL608e printers have no match in the industry. Built in the tradition of SATO's rugged dependability the CL608e printers are based on RISC processors delivering high-quality images at high speeds. Overview The SATO Driver for Mac OS X system was developed to allow the users to print into the SATO printer. This driver is based on CUPS printing system for Mac OS X. All the device communications are handled by CUPS (backend). Software Home - Windows Printer Driver: Windows Printer Drivers SATO Printer Drivers for Windows The SATO Windows Printer Drivers support all the current printer models. These printer drivers are to be used with labeling software and other Windows based programs on. The CL608e printer deliver performance at an affordable price! The CL608e is an advanced performance, high value printer that is truly a SATO through and through. The CL608e features a 32-bit, high speed RISC processor for maximum performance.